Hi all
i have a 4 inch lift dual wheel carrier, long range fuel tank which weighs in at arund 155 kg. i need a heavy duty constant load but what kg? is 350kg plenty to hold rear of car up maybe get drawers later.
i have 150kg on at min wrong springs shocking at rear. dobinson springs
this...
That's what I was thinking Shane. Just getting new springs same ones mate just more of a heavier load. These new springs got on have only been on 2 months can sell them put money towards new springs.
will a constant heavy duty heavier load Spring 350kg hold it higher. With it sagging so much...
Hello all.
i got 4inchlift on my 80s they sent me wrong rear coil springs and I cannot get refund from eBay paypal e.t.c.
they sent me a constant load of 150kg. I have a dual wheel carrier does two tyres, a long range fuel tank all in weighs around135kg. The rear sits 2 inches lower than the...
Hi my car after my 4 inch lift sits lower on drivers compared to passengers side by 25 mm 1 inch.
checked Spring says front right and left and it is ok but as the spy's left is that from inside of car. front right in car and is drivers but from outside car looking forward f right is passengers ?
Asked this before in another segment just want a new thread on it.
when measuring a 4 inch lift from the bottom off wheel arch to the arch or flares, what is it in mm..
Anyone know now any off these measurements a 2 inch 3 and 4 inch from bottom off rim to the flare :icon-cool:
john
Are these measurements good for lift 4inch. I have seen some look lower. Don't know what it is meant to be.
does anyone know measurements of lift 2inch, 4 inch, 6inch always wondered about the measurements
M this is left hand side passengers side 880/885. Right hand side 860mm. Can check out see what you think measurements are. Checked Spring front leftis passenger and opposite drivers side
I got a 4 inch lift on my 80s around 10 days ago and noticed it is 1 inch lower on drivers side than passengers.i got dobinson brand springs, commando shocks iron man caster plates break lines diff breathers pan hard front rear sway bar extension bracket. Had to get bushes for
I still ill have...
Hi
I got my 4 inch lift on 33s mickey ts muddies. Anyone know what the measurement should be in mm when measured from rim to arch(flare) I think measure from bottom of rim.
I heard standard height is 525mm ?.
anyone know what 2 3 and 4 inch is in my.
thanks hope can help
Hi all
im going crazy here what i need to know is How on earth do you get the rear sliding windows out need new rubber all decayed worn out. also got slight bit of rust will get that done straight away at same time.
any got videos of it.
where can i buy new rubber seal for round window.
i...
Hi all
can anyone tell me, how do measure the lift size of your vehicle from the rims.
is it from bottom rim to the arch of vehicle flares
i got 3 inch must have sagged to a 2 maybe less.
Got dobinson coils 3 inch in mm's how do I measure to see exactlly how far it has raised.
got bulbar...
Hi all
looking for 3 inch 75mm coil spring lift for the 80s was considering efs tough dog or dobinson heavy duty.
roothy replied to my question on Facebook recommended terrain tamer
said his mate runs them extreme heavy duty I just looking for constant load of 400kilo f/ and back
what you all...
When you say the window slider what is that mate.Cheers I know the outer of the rubber can be peeled back from over the metal frame where glass is, and there is a rubber piece you can pull out that goes right out the window. Don't know what to do ?
Hello all
i have tried but cannot do it, how on earth can you take the sliding windows out my cruiser. Got bad rust under rubber.
any pics out there of who has done it
got the hdj80 4.2 turbo diesel 1ht-d engine
Hi guys
i have some rust coming out from under rubber from my back window and the small sliding window at side but I cannot get it out.
anyone help
jock
I went to gregge glass glazing company they took out my shattered glass and put a mirror in that they made and it moves as a powered mirror does They made a template cut out miror and glued it on I believe.
Hi all
my truck has Monroe shocks peddles bar and king springs on it when I got it 6 months ago. I am looking for 3 inch lift maybe 4 at very most.
Whats ts everybody preference, dobinsons, rancho, pedders iron man?
got mtzs 33s has 2 inch lift but sagged
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.