Don't like the adverts?  Click here to remove them

Recent content by jef

  1. jef

    Hotwiring a new rear locker stuck in closed position

    I put 12V over the 2 power pins (measured 290ohms so I thought I had the right ones) and alot of sparks later I have blown traces all over my ECU.
  2. Scherm­afbeelding 2023-03-26 om 18.26.00.png

    Scherm­afbeelding 2023-03-26 om 18.26.00.png

  3. jef

    Hotwiring a new rear locker stuck in closed position

    thanks,I got the locker to unlock by putting voltage on the 2 an 3 connector pin. Is there a way to test the relays to see if they are working? The only thing that stands out is that I get 12V over pin 2 and 13 while the manual says I should get 0,5V or less
  4. Scherm­afbeelding 2023-03-26 om 18.25.50.png

    Scherm­afbeelding 2023-03-26 om 18.25.50.png

  5. Scherm­afbeelding 2023-03-26 om 18.26.00.png

    Scherm­afbeelding 2023-03-26 om 18.26.00.png

  6. jef

    Hotwiring a new rear locker stuck in closed position

    Hello! Is there a way to hotwire a rear locker stuck in a closed position? I just replaced my broken rear locker with a brand new one because the old one did not work anymore. The casing was completely rotted and broken because of galvanic corrosion. The new locker came in the closed position...
  7. Scherm­afbeelding 2023-03-26 om 09.51.45.png

    Scherm­afbeelding 2023-03-26 om 09.51.45.png

  8. Scherm­afbeelding 2023-03-26 om 09.40.30.png

    Scherm­afbeelding 2023-03-26 om 09.40.30.png

  9. jef

    Acceleration problems 1HDFT

    Recently I noticed when I'm accelerating hard in 2nd gear around 2700-3100 rpm (also in 3rd but not so much) its gets realy jerky (moments when I lose power then power again), looks like I'm not getting enough fuel/boost? Where do I start to look?
  10. jef

    Looking for a good offset for a new set of rims

    thats why I want to change, lost the bead at both sides while offroading. There was a lot of dirt inbetween the rim and the tire.
  11. jef

    Looking for a good offset for a new set of rims

    I'm currently looking to upgrade from 285 75 r16 to 315 75 r16 mud terrains but looking for a good set of rims, my current rims are a bit to wide, have only 4 of them and the dimensions are a bit unknown. A wild guess is 16x10 et-? around 30 I think. Is 16x8 et-25 a good choice? I want the...
  12. IMG_0640.png

    IMG_0640.png

  13. jef

    Timing belt snapped (1HD FT 300.400km)

    No, I replaced the head
  14. jef

    Timing belt snapped (1HD FT 300.400km)

    A final update: Had to replace the head due to one broken camshaft bearing cap, which was a bummer because the only other damage that was done was a cracked rocker shaft and one broken rocker. No damage to the valves (were checked and all dead straight) and no damage to the pistons (only a very...
  15. jef

    Damaged abs ring front CV

    The end of the ABS sensor looks just fine. Could play in the bearings caused the bell to have touched the underside of the axle housing?
Back
Top