Search results

Oil and filter, primary and secondary fuel filter, air filter and coolant. Service by Gasmanjc posted Apr 17, 2018 at 3:45 PM Service parts by Gasmanjc posted Apr 17, 2018 at 3:45 PM

I have been looking at something similar here. Difference is they tuck under the plastic trims. Not sure if its worth the hassle to remove when cleaning though.

Does the FJ have the pump between the 2 tanks like the prado. These can fail only allowing you to fill half a tank

Maybe some pics would help mate

Hi Victor. They are the tongue out of red tongue floor boarding, There is yellow and blue also.

Looks Tidy mate. Bet it goes like cut snake!

I dont think the 2.8 chips would be the same as the 3.0. Different Engine.Safest bet is to get a custom tune done on a dyno. I would imagine though that there would be plenty of chips available for the 2.8.

With that tutorial how could you go wrong hahaha. I almost want to start spelling the way I talk for the amusement of non Australians here. I could imagine some of the pommy gits here would have some pretty interesting lingo also:laughing: . I work with an older pom and he messes with me like that.

A+ thread. Will read again.

Heres a couple more for the list Aussie Four Wheelers https://www.youtube.com/channel/UCkgNx6AVxTvtkhvd4_XJwzA JOHN ROOTH https://www.youtube.com/channel/UCZ86X313lC-_h_c7WLHL4gQ Roaming The Outback https://www.youtube.com/channel/UCqZ-Oz4HKDxPdqsffsoIOrg Seriously Series...

From what I can tell your new battery is 570cca which to me isn't good enough for a diesel. I just removed a 720cca which I assumed was the factory battery and put in a 750cca. Its difficult to find much info.

Been a member there for a while. Nowhere near as welcoming as this Forum. Get the impression your not quite good enough over there.

Hi Mate in regards to the Winch question, It may depend on the strength of the Cradle its attached to. My TJM bar is only rated to take the load a 9000lb winch can produce. I went 12000lb anyway . Best talk to the guy whos building the Bar I guess. What happened to the pics?

Amazing project mate! Im no welder but the welds look ok. im flat out getting 2 bits of paper together with some masking tape. Check out the Drifta 270° Awning for some inspiration. It is very well built also. They have made the rear section square with the vehicle which gives more...

I have a set of Tredz. I haven't been stuck enough to you them yet though. In comparison to maxtrax though they are much sturdier, so a single one could be used for bridging. On the downside this means they are more brittle and easier to break than maxtrax . Maxtrax will deform to the shape of...

nice one mate. Surprised there is a v6 model. Over here we get v8 turbo diesel or v8 turbo diesel ! Im guessing its the same v6 petrol that the aussie 150 had in it until recently.

Just keep in mind that you cant access the bolts furthest from the rear from the handle end of the drawers. I designed mine in such away that the back of the carcass could be removed gaining the access needed .

Thanks Hamba, I removed the bolts from the factory tie downs that were in the backs of the seats/floor . I swapped them out for 50mm bolts and big washers and bolted through the bottom of the carcass. I didn't need to countersink as first planned as the slides together (8mm) were high enough to...

Finally got around to having the Drawer table edged. I was originally going to do a wood grain edge to match some of the Interior bits but black seems to work well. Also stained the top , came up a treat. Edged and stained by Gasmanjc posted Jan 26, 2018 at 8:58 AM Done by Gasmanjc posted Jan...

I think mine are a little low since adding the bar and winch. Apparently the adjustment for the vx/kakadu is near the rear axle. Some sort of level the headlights work off

Replaced the cranking battery today. It didnt want to play this morning. 750CCA up from 720

Replaced front and rear brake pads. The ones I removed had about %30 left so they've gone into the spares box.Thought I would adjust the hand brake while I was there. Bad Idea. Long story short , I messed up and one of the shoe retainers popped off. There were some interesting grinding noises...

Yeah now I just gotta get around to washing her

Finally got some new underbody protection. 4mm Silver Zinc plated steel from Bushskinz 4x4. It came in 3 pieces weighing nearly 35kg , covering from the radiator to just behind the transfer case. Factory plates are a little munted Before Pic by Gasmanjc posted Jan 12, 2018 at 11:55 PM After...

Well used factory plates

All done

Beautiful car Mate

First cut! Measured the space in the wagon and set to work building the carcass first cut by Gasmanjc posted Dec 29, 2017 at 12:03 PM After test fitting the carcass I realised that if I was to fit a fridge I would need to lower one side test fit by Gasmanjc posted Dec 29, 2017 at 12:03 PM...

I recently embarked on a rear drawer system build. I managed to do it with limited tools and resources but am pretty happy with the outcome. Here's how it went down! Power tools: Circular saw $98 , Drill , Belt sander Hand tools: Curved scalpel , sanding block , Scissors , chalk line , chalk ...

first design

fridge wont fit so modified it

carpet done

8kg magnetic latches

showing runners and black painted sides

painting all visible timber

installed closed

installed open

Installed table extended

2400 x 1200 15mm ply

Building my rear drawers LC 150